Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
guides:esxi_host_bootstrap [2019/03/09 00:45] djmurray [3. First Boot] |
guides:esxi_host_bootstrap [2019/07/27 21:07] pngebura |
||
---|---|---|---|
Line 28: | Line 28: | ||
* Select "Set Static IP" | * Select "Set Static IP" | ||
* Enter the correct information. See [this page](/cdr/networks/management) for detailed information | * Enter the correct information. See [this page](/cdr/networks/management) for detailed information | ||
+ | * IPv4 Address: Check IP Ranges | ||
+ | * Subnet Mask: 255.255.255.192 | ||
+ | * Default Gateway: 128.205.44.129 | ||
* Go to "IPv6 Configuration" | * Go to "IPv6 Configuration" | ||
* Disable it | * Disable it | ||
Line 49: | Line 52: | ||
* Username: root | * Username: root | ||
* Password: <the password you setup> | * Password: <the password you setup> | ||
- | * Enable Lockdown Mode | ||
* Press continue through everything else | * Press continue through everything else | ||
+ | * Enable Lockdown Mode | ||
+ | * Configuration -> Security Profile -> Lockdown Mode (Normal, not Strict) | ||
+ | |||
After a bit, the host should show up in the cluster you added it to. Woot! Now, setup the reset of the network connections, and datastore connections | After a bit, the host should show up in the cluster you added it to. Woot! Now, setup the reset of the network connections, and datastore connections | ||
===== 5. NICs ===== | ===== 5. NICs ===== | ||
- | * Modify Management Network, change name to "DO NOT USE - CSE Management Network" from "VM Network" | + | Host : `Configure` : `Networking` : `Virtual switches` |
- | * Enable vMotion for that switch | + | * Modify the [Management Network](/cdr/networks/management) switch |
- | * Add a new NIC: [direct-io](/cdr/networks/direct-io) | + | * Change name to "DO NOT USE - CSE Management Network" from "VM Network" |
- | * VMKernel | + | * Enable vMotion for the port on that switch (This is located below "VMkernel Ports" Menu. |
- | * To to vDS, add [vds-core-nets](/cdr/networks/vds-core-nets) and [vds-team-nets](/cdr/networks/vds-team-nets) | + | * Add a new NIC and vSwitch for [Direct IO](/cdr/networks/direct-io) |
+ | * VMkernel Network Adapter | ||
+ | * New standard switch | ||
+ | * Select appropriate adapter | ||
+ | * Use the network label `direct-io` | ||
+ | * Use [static IPv4 settings](/cdr/networks/direct-io) | ||
+ | * Virtual Machine Port Group | ||
+ | * Use the existing switch created above | ||
+ | * Use the network label `io-net` | ||
- | ===== 6. iSCSI ===== | + | From the Networking section of vCenter (i.e. not for the specific host) |
+ | * Add the host to [vDS](/misc/what_is_vds) (both [vds-core-nets](/cdr/networks/vds-core-nets) and [vds-team-nets](/cdr/networks/vds-team-nets)) | ||
+ | |||
+ | ===== 6. NTP ===== | ||
+ | Host : `Configure` : `Time Configuration` | ||
+ | * Use Network Time Protocol | ||
+ | * NTP Servers: `tick.cse.buffalo.edu, tock.cse.buffalo.edu, ticktock.cse.buffalo.edu` | ||
+ | * Start NTP service | ||
+ | |||
+ | ===== 7. iSCSI ===== | ||
+ | Host : `Configure` : `Storage` : `Storage Adapters` | ||
* Add Software iSCSI Adapter | * Add Software iSCSI Adapter | ||
* Dynamic Discovery | * Dynamic Discovery | ||
Line 67: | Line 90: | ||
* 10.0.0.155 | * 10.0.0.155 | ||
* 10.0.0.160 | * 10.0.0.160 | ||
+ | * Rescan the ISCSI Adapter | ||
+ | ===== 8. Host datastore ===== | ||
+ | At this point, you should already have the iSCSI servers connected. The host's own datastore is also connected. | ||
+ | * Rename the host's datastore to `datastore-vhostX` | ||
+ | * Move the datastore into the `Host Datastores` folder | ||
- | + | ===== 9. Bask in your Awesomeness ===== | |
- | ===== 7. Bask in your Awesomeness ===== | + | |
{{:guides:gg.jpg?400|}} | {{:guides:gg.jpg?400|}} | ||